Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[FLSTFI Dave]

Wish they would do a version where the VVT could be kept.

[BigLew]

Yeah I asked that question. The answer kind of made sense. We will see! Dave you going to MV

BigLew

[FLSTFI Dave]

I doubt I will be going to Maggie valley.  My clubs annual party is the last 4 days of it.

[kojak]

Engine swap

[FLSTFI Dave]

Looks really good.  I'm sure the 135 is very nice. 

[kojak]

Looks really good.  I'm sure the 135 is very nice.
[/quote
So finished the initial break-in today. Yesterday, I rode 5 miles all under 2500 rpm and shut it down for 30 minutes. Then rode 12 miles all under 2500 rpm and shut it down for the day. This morning I rode 10 miles under 2500 rpm and shut it down for 30 minutes, Then rode 100 miles all under 2500 rpm and shut it down for 1 hour. The finally rode 50 miles upto 3000 rpm and called it a day. I figure the piston rings are seated by now.
Initial impressions:
1. I had the 131 kit on my 2017 cvo limited and that was a very twitchy throttle and lots of low end torque. This motor is much more tractable and very smooth response from idle. I did mostly HD parts with an extreme ventilator, the SE tuner and kept my KW HP+ slipons. My ride today was so enjoyable, this bike has so much low rpm power and pulls like my HD diesel truck.
2. It hit a high of 80 degrees today and the twin cooled 135 never got uncomfortably hot. Upon shutdown, the fans ran for the same amount of time as the 117 motor.
3. Gas mileage is uncertain so far, if I had to guess its probably in the high 30's.
Im not a dyno guy and this bike will never see the dynometer. My butt is the ultimate measurement. Very satisfied with the power and look forward to putting many miles on this motor.
]

[FLSTFI Dave]

The 135 has a little longer stroke, same bore as the 131.  So that will increase your torque.  Bike should be lots of fun with all that low end torque.

Wish HD would come out with a VVT Cam for the 135.  I would do the kit for my 23.5 VVT CVO

[kojak]

The 135 has a little longer stroke, same bore as the 131.  So that will increase your torque.  Bike should be lots of fun with all that low end torque.

Wish HD would come out with a VVT Cam for the 135.  I would do the kit for my 23.5 VVT CVO

Why is the vvt so important? You can do the kit from 121 to 135 and not have the vvt like the ST CVO. I had to do the crate motor since the kit wouldn't work with the 117 due to the stroke.

[FLSTFI Dave]

Why is the vvt so important? You can do the kit from 121 to 135 and not have the vvt like the ST CVO. I had to do the crate motor since the kit wouldn't work with the 117 due to the stroke.

I like what VVT does for the torque curve.   Yes, I know I could do the 135 and eliminate the VVT.  A few have already done this with nice results.  I should check out the torque curve of the 135.  I know I'M not a fan of the ST CVO torque curve for my intended use as a touring bike.  Its great for a performance bagger.  I have ridden the ST CVO.  Prefer the way my power comes on for touring.

[kojak]

Its the first time I've seen Harley advertise rear wheel HP/Torque on one of their big bore kits like the one for your bike. That is serious power for a factory tune. Im sure you could get another 15 HP out of this kit with after market but still pretty amazing.
"Made for riders seeking maximum displacement, compression, and flow, it delivers 144 horsepower and 149 ft-lb of torque to the rear wheel"

[kojak]

I think the motors they are shipping out now have a bit more power since fuel moto did this run.